Book An Appointment

 

We have encountered this post involving Tools You Need to Install a New Bathtub below on the web and concluded it made good sense to discuss it with you here.

Mounting a bathtub isn't specifically brain surgery, but it does call for solid plumbing, carpentry, as well as in some cases, tiling abilities. Changing an old tub with a new one is likewise a reasonably hard job. If the old bathtub is conveniently available, the job can relocate quickly; if you have to open a wall to remove the old bathtub and also position the brand-new tub, the job is much harder. In either situation, the task is within a residence handyman's skills, although you will certainly need an assistant to move out the old tub and embeded in the brand-new one. Make certain you have qualified yourself for the task and are comfortable trying it. Instead of hiring a specialist to take over a halfway-completed project, it is better to think about utilizing one before you begin. Possibilities are you might need a professional plumber to make tube connections.
This write-up will help you mount a brand-new bathtub in your shower room if you have actually currently acquired a new tub as well as don't need to change the setup of your previous supply of water pipelines.
Your tools and also product list must make up the following:

 

• New Bathtub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Chisel


• Tape Measure


• Pipe Caps


 

Removing Old Taps

If you need to replace old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is detach the water. After doing so, turn on the taps to drain any kind of water continuing to be in the system. The process of eliminating the existing taps can be rather bothersome due to the limited access that is often the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipelines to the taps. Have a fabric all set for the continuing to be water that will originate from the pipelines. As soon as the supply pipelines have been gotten rid of, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the single taps from transforming during this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleaned of any old securing substance.
Before carrying on to fit the new faucets, contrast the pipe links on the old faucets to the new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.

 

 

Suitable New Touches

If the tails of the brand-new taps are plastic, then you will need a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the tap as well as the other end provides a link to the existing supply pipelines.
If you require to fit a monobloc, then you will need reducing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, position the faucet in the installing opening in the bath/basin making sure that the washing machines remain in place between the faucet as well as the sink. Secure the faucet in position with the supplier provided backnut. When the faucet is safely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical faucet ports. The former kind must be connected to the faucet finishes first, tightening up just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have been connected.

 

 

Installing the Bath tub

Utilizing the two wooden boards under its feet, position the bath tub in the called for placement. The wood boards are valuable in equally spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto 4 small points.
The following goal is to ensure that the tub is leveled all round. This can be accomplished by inspecting the spirit level and also changing the feet on the bathtub until the spirit level checks out degree.
To set up faucets, fit the bottom of the outermost flexible faucet port to the ideal supply pipe by making a compression sign up with; then do the very same for the other faucet.
Turn on the water system and also inspect all joints and new pipework for leakages and tighten them if essential. Load the bathtub and likewise inspect the overflow electrical outlet and the regular outlet for leaks.
Ultimately, deal with the bathroom paneling as described in the supplier's instruction manual. Tiling and securing around the bath tub must wait up until the tub has actually been utilized a minimum of once as this will settle it right into its last position.

 

 

Planning for the Installation

Firstly, the sustaining framework supplied with the bathroom ought to be fitted (if required) according to the producer's instructions. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is necessary to ensure that if the faucet features a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bath, it is also practical to fit a supporting plate under the taps unit to prevent strain on the bath tub.
Fit the versatile tap adapters to the bottom of both faucets utilizing 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet via the hole in the bath. Make use of the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make certain you use every one of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath should now prepare to be suited its last setting.

 

 

Tiling Around the Bathtub

In the area where the bathroom fulfills the tile, it is needed to seal the joins with a silicone rubber caulking. This is very important as the fitting can move sufficient to break a stiff seal, creating the water to penetrate the wall surface in between the bathroom and also the tiling, leading to problems with dampness and possible leakages to the ceiling listed below.
You can choose from a variety of coloured sealers to assimilate your fixtures and fittings. They are sold in tubes and cartridges, and can sealing gaps as much as a width of 3mm (1/8 inch). If you have a larger void to load, you can load it with spins of soaked paper or soft rope. Remember to constantly fill the tub with water before securing, to permit the activity experienced when the bathtub is in use. The sealant can break fairly early if you do not consider this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally easily offered on the market. It is advisable to fit the ceramic tiles using waterproof or water resistant glue and cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

I ran across that content on Installing A Bathtub while doing a lookup on the web. Enjoyed reading our write-up? Please share it. Let another person locate it. Thank-you for your time invested reading it.

Always here, call!